รุ่นนี้ใช้กับ sim3g,sim4g ได้แล้วนะครับ  DTAC,AIS ทดสอบมาหมดแล้วครับ

รุ่นนี้สามารถต่อลำโพงได้โดยตรง สามารถรับและส่งค่า dtmf ได้โดยตรงไม่ต้องใช้ mt8888 mt8870 คับ


datasheet
https://cdn-shop.adafruit.com/datasheets/sim800h_hardware_design_v1.00.pdf

 

ความเร็วเริ่มต้น 115200bps แก้ความเร็ว9600bps  ใช้ AT+IPR=9600

Module Model: SIM800L (latest module performance over SIM900 / M590)

Operating voltage: 3.7 ~ 4.2V (current peak 1A, please get processed)

Support Network: China Mobile, China Unicom and global quad-band network

Module size: 2.5cmx2.3cm

Serial to TTL serial port, can be directly linked to the MCU. You do not need MAX232

The power module automatically boot, homing network

Onboard one signal light (the signal slow flash, no flash signal)

The world's smallest size, by no less than this module is a GSM module

Full-chip processing machine, reflow soldering, stable performance

Lithium battery power supply can be directly, can also be used 5V power supply,

 

Specifications

• Quad-Band GSM 850/900/1800 / 1900MHz
• GPRS multi-slot class 12/10
• GPRS mobile station class B
• GSM 2/2 +FM frequency between 76 MHz and 109 kHz adjustable by step 50AT command set support (3GPP TS 27.007, 27.005 and augmented by SIMCOM AT)
  • Class 4 (2W at 850 / 900MHz)
  • Class 1 (1 W at 1800 / 1900MHz)
• Serial interface
• Supply Voltage: 3.4 - 4.4 V
• It works between -40 and +85 ° C
• GPRS class 12, maximum of 85.6 kbps
• PBCCH support
• Supports coding schemes CS 1, 2, 3, 4
• PPP stack
• CSD up to 14.4 kbps
• Supports USSD
• Supports SMS
• Supports text mode and PDU mode
• 0710 MUX protocol support
• Integrated support for TCP / UDP
• Supor FTP / HTTP
• MMS
• E-mail
• DTMF detection
• TricodecAMRHalf Rate (HR)
  • Half Rate (HR)
  • Full Rate (FR)
  • Enhanced Full Rate (EFR)
• Full Rate (FR)
• Supports echo cancellation algorithms
• SIM card interface 3 V / 1.8 V

Usage with Arduino

GSM module with chip SIM00L is very popular in the community Arduino. It provides GSM (Global System for Mobile Communications) and GPRS (General Packet Radio Service) and SMS, USSD, voice and internet services support for TCP, UDP, HTTP and FTP.

The module is supplied with a voltage of 3.4 V to 4.4 V and communicates with plate Arduino via serial interface. The operating mode is similar to Wifi module ESP-01: module receives a serial number of preset commands for accessing functions. The module responds to AT command set. For proper feeding, you can use an adjustable source, very useful if several projects with Arduino or a small fitting with regulator LM317 - a source linear variable output.

SIM800 module to communicate with SoftwareSerial.h we use library that allows us to use other digital pins for serial communication. For other details, such advantages or limitations examples of this library, you can access the following link:
http://cartearduino.ro/v1/link42.0

We will use terminals 8 and 7 for connections with pins TX or RX of the GSM module. We will present a program that sends commands and displays them on serial. Examples of commands:
• AT - check the functionality
• ATZ - Reset initial configurations
• AT + GCAP - Get a full list of capabilities
• AT + GMI - Request manufacturer ID
• AT + GMM model-Sky ID
• ATA - Answer incoming
• ATD - Make a call to the number in memory
• aT + CFUN - Sets functionality
• aT + CFUN? - Display current settings AT + CFUN

SIM800 command set is supported by very large, they have the possibility to receive various parameters and variations. Mobile phones operate using similar command sets.
 

Use GSM modules with Arduino
AT command set supported by SIM800L

Downloads

•  SIM800 Series_IP_Application Note_V1.00.pdf
•  SIM800_Series_FM_Application_Note_V1.pdf
•  SIM800_Series_Serial_Port_Application_Note_V1.01.pdf

ส่วนโปรแกรมสำหรับทดสอบบนคอม และ driver ที่อยู่ใน web ผมเข้าไปที่นี่ครับ ไม่มี password ครับ ไม่ต้องกรอกใดๆ
Download SOFTWARE&Souce Code ของ บอร์ดทดลองและเครื่องโปรแกรมชิพMCS51 ,AVR ทุกรุ่น sp200,sp300 ที่ผมขาย ทั้งหมดที่นี่ครับ



ex1 ทดสอบการโทรออก
void setup() {
   // initialize serial communication at 9600 bits per second:
   Serial.begin(9600);
}
 
// the loop routine runs over and over again forever:
void loop()
{
   delay(3000);
   delay(3000);
   delay(3000);

   // print out the value you read:
     Serial.print("ATD08976542XX;");
     Serial.write(13);

   delay(3000);
   delay(3000);
   delay(3000);
   delay(3000);
   delay(3000);
   delay(3000);
   delay(3000);
   delay(3000);
   delay(3000);


}



โมดูลGSM sim900ร่วมกับarduino
ex2 ส่ง sms
// the setup routine runs once when you press reset:
void setup() {
   // initialize serial communication at 9600 bits per second:
   Serial.begin(9600);
}
 
// the loop routine runs over and over again forever:
void loop() {
   delay(3000);
   delay(3000);
   delay(3000);

   // print out the value you read:
     Serial.print("AT+CMGS=");
         Serial.write(");
      Serial.print("+66897654231");
         Serial.write(");
         Serial.write(13);

   delay(3000);

         Serial.write(13);
     Serial.println("hello");
         Serial.write(26);
         Serial.write(13);
    while(1);
}

โปรแกรมส่ง sms กับ mcs51

sbit testsms = P3^4;//for test send sms


void delay(unsigned int i)   //หน่วงเวลา
{
    for(i=i;i>=1;i--);
}

void sms(void)
{      

       send('A');
       send('T');
       send('+');
       send('C');
       send('M');
       send('G');
       send('S');
       send('=');
       send('"');
       send('+');
       send('6');
       send('6');
       send('8');
       send('3');
       send('0');
       send('7');
       send('9');
       send('4');
       send('7');
       send('0');
       send('3');
       send('"');
       delay(100);
       send(13);
delay(30000);delay(30000);delay(30000);delay(30000);
delay(30000);delay(30000);delay(30000); delay(30000);          
delay(30000);delay(30000);delay(30000);delay(30000);
delay(30000);delay(30000);delay(30000); delay(30000);          
delay(30000);delay(30000);delay(30000);delay(30000);
delay(30000);delay(30000);delay(30000); delay(30000);          
delay(30000);delay(30000);delay(30000);delay(30000);
delay(30000);delay(30000);delay(30000); delay(30000);          
       send(13);
       printf("level beep is %d",beep);
       send(13);
        printf("danger  ");
        send(13);

        delay(100);
        send(26);
       send(13);

    

}



void main(void)
{ TH1=0xfd;TL1=0xfd;TMOD=0x20;
            SCON=0X52;TR1=1;
   
st: if(!testsms)
{ sms();
}
goto st;
}